Trigonometric series solution for natural vibration characteristics of simply supported steel-concrete composite beams considering interface slip and damping effect
-
摘要:
为得到简便且力学机理明确的自振频率计算公式,采用剪力连接件抗剪刚度表征界面滑移效应,建立了阻尼效应与抗剪刚度关系式;利用三角级数构造组合梁时变位移响应和界面滑移函数,基于哈密顿原理推导得到了考虑界面滑移和阻尼效应协同作用的竖向自振频率解析解,并在此基础上提出了实用的自振频率折减系数简化公式;通过与大量既有文献中的振动模态实测值和计算方法比较分析,验证了其有效性和准确性。研究结果表明:考虑界面滑移和阻尼效应后,对钢-混组合梁基频折减可达17%;界面滑移和阻尼效应主要影响低阶(前5阶)自振频率,对高阶影响很小;阻尼比随振型阶数增加而增加,随抗剪刚度增大而减小,推荐阻尼比按1%取值。相比既有计算方法,考虑界面滑移和阻尼效应的三角级数解适用于不同连接程度(抗剪刚度、栓钉间距)简支钢-混组合梁自振频率计算,简洁直观,物理意义明确,计算精度更高。
Abstract:To derive a simplified and mechanically rigorous formula for the natural vibration frequency, the shear stiffness of the shear connectors was employed to characterize the interface slip effect. The relationship between the damping effect and the shear stiffness was established. Subsequently, trigonometric series were utilized to construct the time-varying displacement response and the interface slip function of the composite beam. By applying Hamilton's principle, an analytical solution for the vertical natural vibration frequency was derived with the synergistic effect of both interface slip and damping taken into account. Building on this, a practical simplified formula for the natural vibration frequency reduction coefficient was proposed. Finally, through a comparative analysis with an extensive body of existing literature on both measured vibration modes and calculation methods, the effectiveness and accuracy of the proposed approach were validated. The results indicate that after considering interface slip and damping effects, the fundamental frequency of steel-concrete composite beams can be reduced by up to 17%. These effects primarily influence the lower-order natural vibration frequencies (first five modes), with a negligible impact on higher-order modes. The damping ratio increases with the higher mode order and decreases with greater shear stiffness. A damping ratio of 1% is recommended for practical applications. Compared to existing calculation methods, the trigonometric series solution considering interface slip and damping effect is applicable to calculating the natural vibration frequencies of simply supported steel-concrete composite beams with varying connection degrees (shear stiffness and stud spacing). It is more concise, physically intuitive, and offers higher computational accuracy.
-
表 1 剪力连接件基本参数及组合梁阻尼比
Table 1. Basic parameters of shear connectors and damping ratio of composite beams
数据来源 试件 连接件类型 直径/mm 间距/mm ns K/MPa 前5阶阻尼比/% 文献[27] CB1 栓钉-均布 13 370 2 1 213 0.82、1.27、1.18、1.35、1.55 CB2 栓钉-均布 13 300 2 1 496 0.59、1.26、1.33、1.17、8.33 CB3 栓钉-均布 13 230 2 1 951 0.52、1.07、1.21、0.98、8.33 CB4 栓钉-均布 13 150 2 2 991 0.48、0.82、1.06、0.97、0.98 CB5 PBL键 ∞ 0.41、0.99、0.67、0.48、无 文献[28] EB1 栓钉-非均布 22 290、125、90 4 3 036 EB2 栓钉-非均布 22 500、480、250、150 4 1 574 文献[29] SCB1 栓钉-均布 13 150 2 2 694 SCB2 栓钉-均布 13 250 2 1 616 SCB3 栓钉-均布 13 400 2 1 010 表 2 组合梁竖向弯曲自振频率分析结果对比
Table 2. Analysis result comparison of vertical flexural natural vibration frequencies in composite beams
Hz 试件 f1 f2 f3 f4 f5 前5阶理论值与实测值之比 实测 理论 实测 理论 实测 理论 实测 理论 实测 理论 CB1 28.74 32.36 97.18 115.18 194.13 236.53 324.58 397.16 404.55 599.07 1.13、1.19、1.22、1.22、1.48 CB2 29.99 32.76 99.54 117.93 198.07 242.19 346.21 405.07 437.47 608.53 1.09、1.18、1.22、1.17、1.39 CB3 31.25 33.20 102.52 121.31 201.37 249.78 363.09 416.31 455.01 622.46 1.06、1.18、1.24、1.15、1.37 CB4 32.52 33.74 109.90 126.25 205.41 262.46 379.60 436.83 481.90 649.44 1.04、1.15、1.28、1.15、1.35 CB5 34.65 34.94 123.07 141.21 244.29 318.34 438.93 566.32 1.01、1.15、1.30、1.29、无 EB1 20.00 21.96 65.44 80.85 1.10、1.24、无、无、无 EB2 19.38 20.87 63.13 74.52 1.08、1.18、无、无、无 SCB1 15.26 20.86 1.37、无、无、无、无 SCB2 14.60 20.75 1.42、无、无、无、无 SCB3 14.21 20.60 1.45、无、无、无、无 表 3 组合梁频率折减系数对比
Table 3. Comparison of frequency reduction coefficients in composite beams
试件 α1 α2 α3 α4 α5 前5阶理论值与实测值之比 实测 理论 实测 理论 实测 理论 实测 理论 实测 理论 CB1 0.83 0.91 0.79 0.81 0.79 0.73 0.74 0.70 0.68 1.10、1.02、0.92、0.95、无 CB2 0.87 0.92 0.81 0.83 0.81 0.75 0.79 0.73 0.69 1.06、1.02、0.93、0.92、无 CB3 0.90 0.94 0.83 0.86 0.82 0.77 0.83 0.73 0.70 1.04、1.04、0.94、0.88、无 CB4 0.94 0.95 0.89 0.89 0.84 0.81 0.86 0.77 0.73 1.01、1.00、0.96、0.90、无 CB5 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00、1.00、1.00、1.00、1.00 EB1 0.87 0.80 EB2 0.83 0.74 SCB1 0.96 SCB2 0.95 SCB3 0.94 表 4 不同计算方法自振频率对比
Table 4. Comparison of natural vibration frequency of different calculation methods
Hz 分析方法 EB1 EB2 f1 f2 f1 f2 试验实测[28] 20.00 65.44 19.38 63.13 有限元[28] 21.71 67.70 21.08 63.09 考虑纵向刚度分布的EBT模型[28] 23.43 82.37 22.27 75.96 修正静力折减刚度的EBT模型[8] 22.29 80.04 21.38 74.67 动力刚度折减的EBT模型[11] 23.43 82.37 22.27 75.96 子梁独立剪切角假设TBT模型(连续)[18] 22.75 75.41 21.67 70.20 子梁独立剪切角假设TBT模型(简支)[21] 22.31 71.59 21.28 67.02 子梁等剪切角假设TBT模型[30] 23.00 77.85 21.90 72.32 本文提出的三角级数解 21.96 80.85 20.87 74.52 -
[1] WANG X H, YANG Q W, PENG X, et al. A review of mechanical performance studies on composite concrete beams and slabs[J]. Materials, 2025, 18(14): 3259. doi: 10.3390/ma18143259 [2] NIE J G, CAI C S. Steel-concrete composite beams considering shear slip effects[J]. Journal of Structural Engineering, 2003, 129(4): 495-506. doi: 10.1061/(ASCE)0733-9445(2003)129:4(495) [3] 侯忠明, 夏禾, 张彦玲. 栓钉连接件抗剪刚度对钢—混凝土结合梁自振特性影响研究[J]. 中国铁道科学, 2012, 33(6): 24-29.HOU Zhong-ming, XIA He, ZHANG Yan-ling. The influence of the shear stiffness of stud connectors on the natural vibration characteristics of steel-concrete composite beams[J]. China Railway Science, 2012, 33(6): 24-29. [4] 聂建国, 沈聚敏, 余志武. 考虑滑移效应的钢-混凝土组合梁变形计算的折减刚度法[J]. 土木工程学报, 1995, 28(6): 11-17.NIE Jian-guo, SHEN Ju-min, YU Zhi-wu. A reduced rigidity method for calculation deformation of composite steel-concrete beams[J]. China Civil Engineering Journal, 1995, 28(6): 11-17. [5] 王景全, 吕志涛, 刘钊. 部分剪力连接钢-混凝土组合梁变形计算的组合系数法[J]. 东南大学学报(自然科学版), 2005, 35(增1): 5-10.WANG Jing-quan, LV Zhi-tao, LIU Zhao. Consistency factor method for calculating deformation of composite steel-concrete girders with partial shear connection[J]. Journal of Southeast University (Natural Science Edition), 2005, 35(S1): 5-10. [6] 叶华文, 蒋成川, 黄澳, 等. 基于三角级数解的钢-混凝土组合梁弹性弯曲变形计算方法[J]. 建筑结构学报, 2024, 45(5): 253-261.YE Hua-wen, JIANG Cheng-chuan, HUANG Ao, et al. A novel theoretical method of elastic bending deformation of steel-concrete composite beams based on trigonometric series solution[J]. Journal of Building Structures, 2024, 45(5): 253-261. [7] 邓继华, 何子谙, 贺君, 等. 考虑剪切变形的钢-混组合梁时变分析的精确有限元法[J]. 交通运输工程学报, 2026, 26(5): 111-124.DENG Ji-hua, HE Zi-an, HE Jun, et al. Exact finite element method for time-dependent analysis of steel-concrete composite beam considering shear deformation[J]. Journal of Traffic and Transportation Engineering, 2026, 26(5): 111-124. [8] 张书兵, 王景全, 李明, 等. 考虑界面滑移效应的组合梁自振频率计算的修正折减刚度法[J]. 土木工程学报, 2015, 48(12): 41-49.ZHANG Shu-bing, WANG Jing-quan, LI Ming, et al. A modified stiffness reduction method for calculating the natural frequencies of composite beams considering the effect of interfacial slippage[J]. China Civil Engineering Journal, 2015, 48(12): 41-49. [9] 王辉, 沈锐利, 刘高, 等. 列车荷载作用下大跨度铁路悬索桥纵向运动特性及合理约束体系[J]. 交通运输工程学报, 2026, 26(6): 21-35. doi: 10.19818/j.cnki.1671-1637.2026.232 WANG Hui, SHEN Rui-li, LIU Gao, et al. Longitudinal movement characteristics and rational restraint systems of long-span railway suspension bridges under train load[J]. Journal of Traffic and Transportation Engineering, 2026, 26(6): 21-35. doi: 10.19818/j.cnki.1671-1637.2026.232 [10] 李夏元, 万水, 付理想, 等. 一种考虑波形钢腹板等效剪切变形自由度的新型箱梁单元[J]. 交通运输工程学报, 2025, 25(5): 385-398. doi: 10.19818/j.cnki.1671-1637.2025.05.025 LI Xia-yuan, WAN Shui, FU Li-xiang, et al. A novel box girder beam element considering equivalent shear deformation freedom of corrugated steel webs[J]. Journal of Traffic and Transportation Engineering, 2025, 25(5): 385-398. doi: 10.19818/j.cnki.1671-1637.2025.05.025 [11] 侯忠明, 夏禾, 王元清, 等. 钢-混凝土组合梁动力折减系数研究[J]. 振动与冲击, 2015, 34(4): 74-81.HOU Zhong-ming, XIA He, WANG Yuan-qing, et al. Dynamic reduction coefficients for a steel-concrete composite beam[J]. Journal of Vibration and Shock, 2015, 34(4): 74-81. [12] TANG Q C, ZHU L. Vibration control of the steel-concrete composite box girder bridge with slip and shear-lag effects by MTMDs under the train-bridge interaction[J]. Structural Control and Health Monitoring, 2023, 2023(1): 6696148. [13] XU Q Z, WANG J Q, SEBASTIAN W. Experimental and theoretical study on the dynamic properties of externally prestressed steel-concrete composite beams[J]. Structures, 2025, 80: 109716. doi: 10.1016/j.istruc.2025.109716 [14] 周旺保, 蒋丽忠, 余志武, 等. 考虑剪力滞和滑移效应的钢-混凝土连续组合箱梁自振特性[J]. 中国公路学报, 2013, 26(5): 88-94.ZHOU Wang-bao, JIANG Li-zhong, YU Zhi-wu, et al. Free vibration characteristics of steel-concrete composite continuous box girder considering shear lag and slip[J]. China Journal of Highway and Transport, 2013, 26(5): 88-94. [15] ZHOU W B, JIANG L Z, HUANG Z, et al. Flexural natural vibration characteristics of composite beam considering shear deformation and interface slip[J]. Steel and Composite Structures, 2016, 20(5): 1023-1042. doi: 10.12989/scs.2016.20.5.1023 [16] LUO H, ZHONG H Q, CHEN B C, et al. Sensitivity-based finite element model updating of a scaled steel-concrete composite box girder considering interfacial slip and boundary conditions[J]. Structures, 2026, 84: 110927. doi: 10.1016/j.istruc.2025.110927 [17] YAN L B, CAO L, HE Y K, et al. Dynamic characteristics analysis of three-layer steel-concrete composite beams[J]. Buildings, 2025, 15(8): 1347. doi: 10.3390/buildings15081347 [18] 孙琪凯, 张楠, 刘潇. 考虑剪切变形的连续钢-混组合梁动力特性分析[J]. 振动与冲击, 2023, 42(2): 258-266.SUN Qi-kai, ZHANG Nan, LIU Xiao. Dynamic characteristic analysis of steel-concrete composite continuous beams considering the effect of beam shear deformation[J]. Journal of Vibration and Shock, 2023, 42(2): 258-266. [19] HE G H, YANG X. Dynamic analysis of two-layer composite beams with partial interaction using a higher order beam theory[J]. International Journal of Mechanical Sciences, 2015, 90: 102-112. doi: 10.1016/j.ijmecsci.2014.10.020 [20] TAN M Y, GUO D Q, YANG Q, et al. In-plane and out-of-plane free vibration analysis of thin-walled box beams based on one-dimensional higher-order beam theory[J]. Mechanics of Advanced Materials and Structures, 2024, 31(22): 5638-5652. doi: 10.1080/15376494.2023.2218049 [21] 孙琪凯, 张楠, 刘潇. 考虑剪切变形的钢-混组合梁动力特性解析解[J]. 铁道学报, 2023, 45(6): 161-168.SUN Qi-kai, ZHANG Nan, LIU Xiao. Analytical solution of dynamic characteristics of steel-concrete composite beams considering shear deformation[J]. Journal of the China Railway Society, 2023, 45(6): 161-168. [22] 侯忠明, 夏禾, 张彦玲. 钢-混凝土简支结合梁基本动力特性的解析解[J]. 铁道学报, 2014, 36(3): 100-105.HOU Zhong-ming, XIA He, ZHANG Yan-ling. Analytical solution to dynamic characteristics of simply-supported steel-concrete composite beams[J]. Journal of the China Railway Society, 2014, 36(3): 100-105. [23] 汪维安, 李乔, 赵灿辉, 等. 大跨度体外预应力钢-混组合结构桥梁的动力特性[J]. 公路交通科技, 2013, 30(3): 59-65, 71.WANG Wei-an, LI Qiao, ZHAO Can-hui, et al. Dynamic property of long-span steel-concrete composite bridge with external tendons[J]. Journal of Highway and Transportation Research and Development, 2013, 30(3): 59-65, 71. [24] 张书兵, 王景全, 殷惠光. 组合梁等效阻尼比的两种计算方法及对比研究[J]. 建筑结构学报, 2013, 34(增1): 395-400.ZHANG Shu-bing, WANG Jing-quan, YIN Hui-guang. Comparative study of two calculation methods for equivalent damping ratios of composite beams[J]. Journal of Building Structures, 2013, 34(S1): 395-400. [25] 戚菁菁, 蒋丽忠, 张传增, 等. 界面滑移、竖向掀起及剪切变形对钢-混凝土组合连续梁动力性能的影响[J]. 中南大学学报(自然科学版), 2010, 41(6): 2334-2343.QI Jing-jing, JIANG Li-zhong, ZHANG Chuan-zeng, et al. Effects of interface slip, vertical uplift and shear deformation on dynamic behavior of steel-concrete composite continuous beams[J]. Journal of Central South University (Science and Technology), 2010, 41(6): 2334-2343. [26] 杨仕骏, 阳洋, 王者伟, 等. 基于单辆通行车激励的车桥耦合理论梁式桥阻尼比识别研究[J]. 力学学报, 2024, 56(4): 1098-1109.YANG Shi-jun, YANG Yang, WANG Zhe-wei, et al. Damping ratio identification of beam bridge based on vehicle bridge coupling theory under single vehicle[J]. Chinese Journal of Theoretical and Applied Mechanics, 2024, 56(4): 1098-1109. [27] 王景全, 殷惠光, 张书兵, 等. 钢-混凝土组合梁考虑界面滑移的振动模态试验研究[J]. 建筑结构学报, 2016, 37(2): 142-149.WANG Jing-quan, YIN Hui-guang, ZHANG Shu-bing, et al. Experimental investigation on dynamic properties of steel- concrete composite beams considering effect of interfacial slip[J]. Journal of Building Structures, 2016, 37(2): 142-149. [28] 孙琪凯, 张楠, 刘潇, 等. 基于能量法分析考虑纵向刚度分布的钢-混组合梁自振特性[J]. 振动与冲击, 2021, 40(10): 67-72, 102.SUN Qi-kai, ZHANG Nan, LIU Xiao, et al. Free vibration characteristics of steel-concrete composite beams considering the longitudinal stiffness distribution based on the energy method[J]. Journal of Vibration and Shock, 2021, 40(10): 67-72, 102. [29] 张彦玲, 冯康平, 刘欢, 等. 钢-混凝土组合梁动力特性试验研究[J]. 广西大学学报(自然科学版), 2017, 42(1): 97-107.ZHANG Yan-ling, FENG Kang-ping, LIU Huan, et al. Experimental research on dynamic responses of steel-concrete composite beams[J]. Journal of Guangxi University (Natural Science Edition), 2017, 42(1): 97-107. [30] XU R Q, WU Y F. Static, dynamic, and buckling analysis of partial interaction composite members using Timoshenko's beam theory[J]. International Journal of Mechanical Sciences, 2007, 49(10): 1139-1155. doi: 10.1016/j.ijmecsci.2007.02.006 -
下载: