Volume 19 Issue 3
. 
Turn off MathJax
Article Contents
Article Navigation >  Journal of Traffic and Transportation Engineering  > 2019  >  19(3): 27-35
Next Previous
ZHANG Feng, LIU Jia-qi, GAO Lei, LIU Guan-zhi. Test method of clip bite force[J]. Journal of Traffic and Transportation Engineering, 2019, 19(3): 27-35. doi: 10.19818/j.cnki.1671-1637.2019.03.004
Citation: ZHANG Feng, LIU Jia-qi, GAO Lei, LIU Guan-zhi. Test method of clip bite force[J]. Journal of Traffic and Transportation Engineering, 2019, 19(3): 27-35. doi: 10.19818/j.cnki.1671-1637.2019.03.004
shu

Test method of clip bite force

doi: 10.19818/j.cnki.1671-1637.2019.03.004

  • Geotechnical and Structural Engineering Research Center, Shandong University, Jinan 250061, Shandong, China

More Information
  • Author Bio:

    ZHANG Feng(1978-), male, professor, PhD, zhangfeng2008@sdu.edu.cn

  • Received Date: 2018-12-20
  • Publish Date: 2019-06-25
    Abstract
  • To study the relationship between the mutation segment of tension test curve and the clip bite force when using the lift-off method to test the force of prestressed steel strand, the high-frequency acquisition technique in the resistive pressure sensor was used to test the prestressed steel strand forces of a prestressed concrete beam under and outside the anchorage when the clip disengages. A total of 20 samples were tested. The clip bite force test scheme was designed. A total of 326 samples were tested and the statistical analysis was performed. The calculation formula for the clip bite force considering the tension was established. Through the verification test of 37 samples, the test accuracy of bite force correction results was studied. 257 samples were tested in the actual project, and the test results were compared with the proposed calculated formula results. Research result shows that the clip will break away from the original bite mark when the steel strand extends more than 4.5 mm. However, when the clip disengages during the actual test, the tension will be stopped in time, so the lift-off test will not change the effective prestress of prestressed steel strand under the anchorage and affect the project quality. When installing the clip, if the clip does not completely fit the taper hole of socket, the clip will have a large elastic pressing force in the lateral direction to form an additional friction force. The friction force will completely disappear when the clip is separated from the socket. The change of tension outside the anchorage is not obvious at this moment, so the slope of descending segment of tension test curve obtained by the lift-off method has a dispersion after the peak tension, and it is related to the clip installation precision. The bite force of socket in the lift-off test consists of the transient internal force redistributions under and outside the anchorage. The proposed calculation formula for clip bite force can eliminate the test error caused by the bite force between the clip and the socket, and improve the test accuracy by 6.78%. The test bite force in the actual project is larger than the mutation segment of tension test curve obtained by the lift-off method. Therefore, when using the lift-off method to test the prestressed steel strand, the effective prestress under the anchorage is the difference between the peak value of tension test curve obtained by the lift-off method and the bite force.

     

    • FullText(HTML)
  • loading
    • References(32)
  • [1]
    BAŽANT Z P, YU Q, LI G H. Excessive long-time deflections of prestressed box girders. Ⅰ: record-span bridge in Palau and other paradigms[J]. Journal of Structural Engineering, 2012, 138 (6): 676-686. doi: 10.1061/(ASCE)ST.1943-541X.0000487
    [2]
    ROBERTSON I N. Prediction of vertical deflections for a long-span prestressed concrete bridge structure[J]. Engineering Structures, 2005, 27 (12): 1820-1827. doi: 10.1016/j.engstruct.2005.05.013
    [3]
    TAKÁCS P F. Deformations in concrete cantilever bridges: observations and theoretical modeling[D]. Trondheim: The Norwegian University of Science and Technology, 2002.
    [4]
    FU Dan. Working stress tests of prestressed tendons in ground anchorage[D]. Beijing: Tsinghua University, 2010. (in Chinese).
    [5]
    FU Dan, GUO Hong-xian, CHENG Xiao-hui, et al. Working stress measurement of prestressed anchor cables: detection mechanism and experimental study of lift-off test[J]. Rock and Soil Mechanics, 2012, 33 (8): 2247-2252. (in Chinese). doi: 10.3969/j.issn.1000-7598.2012.08.002
    [6]
    ZHAN Gui-chao, LIU Guan-zhi. Test and analysis on prestressed steel strand tension test based on lift-off method[J]. Highways and Automotive Applications, 2016 (3): 191-193. (in Chinese). doi: 10.3969/j.issn.1671-2668.2016.03.051
    [7]
    ZHAO Yu, HONG Lu-jia, ZHOU Yong-jun. Bearing capacity assessment method for PC box girder by testing stress of tendon[J] Journal of Chang'an University (Natural Science Edition), 2019, 39 (1): 61-69. (in Chinese). doi: 10.3969/j.issn.1671-8879.2019.01.009
    [8]
    LI Rui-ge. Prestress loss of full prestressed concrete beams by dynamic technology[D]. Wuhan: Huazhong University of Science and Technology, 2015. (in Chinese).
    [9]
    AI Hui-lin, CHEN Chao-wei, DAI Wen-da. Study of rapid inspection method for under-anchorage effective prestress in prestressed beams[J]. World Bridges, 2015, 43 (4): 42-46. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GWQL201504011.htm
    [10]
    YU Guo-qiang. The application of prestressed concrete bridge effective prestressed testing technology[J]. Xi'an: Chang'an University, 2013. (in Chinese).
    [11]
    YANG Guo-li, LI Rui-ge. Development and prospect of prestress loss detection in prestressed concrete beams[J]. Sichuan Building Science, 2008, 34 (4): 113-116. (in Chinese). doi: 10.3969/j.issn.1008-1933.2008.04.029
    [12]
    GUO Qi. Theory and method of effective prestress prediction of beam prestressed composite prestressed system[D]. Xi'an: Chang'an University, 2008. (in Chinese).
    [13]
    XU Jiang, WU Xin-jun, SUN Peng-fei. Detecting broken-wire flaws at multiple locations in the same wire of prestressing strands using guided waves[J]. Ultrasonics, 2013, 53 (1): 150-156. doi: 10.1016/j.ultras.2012.05.003
    [14]
    CHEN R H L, WISSAWAPAISAL K. An ultrasonic method for measuring tensile forces in a seven-wire prestressing strand[J]. AIP Conference Proceedings, 2002, 615 (1): 1295-1302.
    [15]
    ZHANG Ben-niu, YUAN Can, CHEN Zhuo-min, et al. Stress measurement of steel strands based on LC oscillation[J]. Journal of Chongqing Jiaotong University (Natural Science), 2017, 36 (3): 8-12. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-CQJT201703002.htm
    [16]
    JIA Qiao-yan. Study on the extant pre-stressed force of the concrete structure in service based on the stress release method[D]. Wuhan: Wuhan University of Technology, 2008. (in Chinese).
    [17]
    OU Jin-ping, ZHOU Zhi, WANG Bo. Smart FRP-OFBG bars and their application in reinforced concrete beams[J]. Chinese High Technology Letters, 2005, 15 (4): 23-28. (in Chinese). doi: 10.3321/j.issn:1002-0470.2005.04.006
    [18]
    ZHOU Zhi, WU Zhan-jun, ZHAO Xue-feng, et al. Smart monitoring technique of concrete structures based on optical fiber Bragg grating sensors[J]. Journal of Functional Materials, 2003, 34 (3): 344-348. (in Chinese). doi: 10.3321/j.issn:1001-9731.2003.03.039
    [19]
    HE Shuan-hai, ZHAO Xiang-mo, MA Jian, et al. Review of highway bridge inspection and condition assessment[J]. China Journal of Highway and Transport, 2017, 30 (11): 63-80. (in Chinese). doi: 10.3969/j.issn.1001-7372.2017.11.007
    [20]
    ZHONG Zheng-qiang, DAI Dian, YUAN Jian-wei. Development and application of prestress testing system based on Hooke theorem[J]. Journal of Central South University (Science and Technology), 2018, 49 (3): 725-731. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-ZNGD201803028.htm
    [21]
    DONG Yan, LIU Jia-qi, ZHANG Feng. Instrument development and engineering application of effective prestressing test under anchor[J]. Journal of China and Foreign Highway, 2017, 37 (5): 117-120. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GWGL201705025.htm
    [22]
    LUO Bin, TANG Shu-ming, CHENG Xiao-hui, et al. Techniques of reverse drawing detection for prestress under anchor[J]. Technology of Highway and Transport, 2012 (1): 12-14, 22. (in Chinese). doi: 10.3969/j.issn.1009-6477.2012.01.004
    [23]
    XIA Jing, YUAN Jian-wei. Research on detection method of effective prestress under anchor by lift-off method[J]. Highways and Automotive Applications, 2016 (6): 210-212. (in Chinese). doi: 10.3969/j.issn.1671-2668.2016.06.056
    [24]
    CHENG Jian-bo, YAO Chen, ZHANG Feng. Experimental study of lift-off method for detecting service stress of prestressed strand[J]. Highways and Automotive Applications, 2015 (3): 181-184. (in Chinese). doi: 10.3969/j.issn.1671-2668.2015.03.052
    [25]
    REN Chuan-ting, LIU Wei-chao, LING Tian-qing, et al. Primary investigation for unevenness of effective prestress[J]. Technology of Highway and Transport, 2015 (6): 63-67, 72. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLJT201506015.htm
    [26]
    WU Yu-cai, ZHANG Guo-bing, LI Fen. Prestressing steel wire drawing force testing technology[J]. Transportation Science and Technology, 2006 (5): 36-37, 59. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-SKQB200605014.htm
    [27]
    HAN Kan, LI Deng-ke, WU Guan-zhong. Pull-out tests on anchoring force of prestressed anchor cables[J]. Chinese Journal of Geotechnical Engineering, 2011, 33 (S1): 385-387. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-YTGC2011S1074.htm
    [28]
    ZHANG Feng, GAO Lei, XU Xiang-feng, et al. Testing technology of under-anchorage effective prestress of steel strand in construction period[J]. Journal of Northeastern University (Natural Science), 2017, 38 (8): 1201-1205. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-DBDX201708028.htm
    [29]
    ZHAGN Feng, GAO Lei, HAN Fu-zhou. Experiment on bite force of prestressed steel wire clip-type anchors[J]. Journal of Basic Science and Engineering, 2017, 25 (6): 1273-1281. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-YJGX201706018.htm
    [30]
    KONG Qing-hua, WANG Si-ling, XIE Qiang. Structure analysis of wedge type single hole prestressed anchor[J]. Grinder and Grinding, 2005 (3): 10-11. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-SCYM200503005.htm
    [31]
    FENG Tian-peng, WANG Dong, HAN Fu-zhou, et al. New testing technology for friction coefficient of prestressed duct[J]. Construction Technology, 2017, 46 (9): 39-42. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-SGJS201709012.htm
    [32]
    SHI Nan-xiang. Inspection and monitoring of prestressed anchoring system[J]. Journal of Chongqing Jianzhu University, 2002, 24 (2): 43-46. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-JIAN200202010.htm
    • Relative Articles
    • Supplements(0)
    • Cited By

Catalog

    Get Citation
    PDF
    XML

    Article Metrics

    Article views (1636) PDF downloads(380) Cited by()
    Related

    Copyright《Journal of Traffic and Transportation Engineering》编辑部陕ICP备05001904号-1

    Address ：Editorial Department of Journal of Traffic and Transportation Engineering, Chang 'an University, Middle Section of South Second Ring Road, Xi 'an, Shaanxi（710064） Tel：029-82334388 Email：jygc@chd.edu.cn

    All visit:Today's visit:

    Supported by: Beijing Renhe Information Technology Co. Ltd    

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return