拱桥汽车设计荷载标准分析

胡大琳; 惠小记; 夏春梅; 李影; 张航

拱桥汽车设计荷载标准分析

1.
长安大学公路学院, 陕西西安 710064
2.
江苏省交通技师学院道路桥梁工程系, 江苏镇江 212028
3.
威斯康星大学麦迪逊分校土木与环境工程系, 威斯康星麦迪逊 53706

基金项目:

交通运输部应用基础研究项目 2013 319 812 100

详细信息

作者简介:
胡大琳(1959-), 男, 陕西蓝田人, 长安大学教授, 工学博士, 从事桥梁结构研究

中图分类号: U441.2
计量
- 文章访问数: 731
- HTML全文浏览量: 152
- PDF下载量: 469
- 被引次数: 0
出版历程
- 收稿日期: 2016-09-21
- 刊出日期: 2017-02-25

Analysis of vehicle design load standard of arch bridge

1.
School of Highway, Chang'an University, Xi'an 710064, Shanxi, China
2.
Department of Road and Bridge Engineering, Jiangsu Jiaotong College, Zhenjiang 212028, Jiangsu, China
3.
Department of Civiland Environment Engineering, University of Wisconsin-Madison, Madison 53706, Wisconsin, USA

More Information

Author Bio:
HU Da-lin(1959-), male, professor, PhD, +86-29-82335772, dlhu@chd.edu.cn

摘要

摘要: 分析了超载车辆对桥梁的影响与现行规范即《公路桥涵设计通用规范》 (JTG D60—2015) 中的汽车荷载标准对公路上运营车辆荷载的适用性, 研究了广深高速公路车辆荷载的动态称重系统(WIM) 实测数据, 利用Monte Carlo方法模拟随机车辆荷载和随机车辆间距, 编制了随机车队加载效应计算程序, 计算了无铰拱跨中和拱脚截面的弯矩效应, 采用极大值分布原理求得荷载效应在设计基准期内的标准值, 给出基于WIM实测数据的汽车荷载标准模型, 并与现行规范中的设计荷载标准进行对比。计算结果表明: 推荐车道荷载作用效应对实测荷载效应包容性和适用性良好, 拱桥跨中弯矩误差小于7%, 当跨径为25~65、110、120m时, 拱脚弯矩误差为5%~11%, 其余跨径时的拱脚弯矩误差小于5%;基于广深高速公路实测荷载推定的荷载标准与现行规范中公路-Ⅰ级车道荷载在无铰拱上产生弯矩效应的比值为1.24~2.18, 平均比值为1.80, 说明广深高速交通量大, 车辆超载超限严重, 根据实测车辆荷载推断的荷载标准与现行规范荷载标准出现了较大偏差, 广深高速桥梁设计荷载标准应在现有规范基础上适当提高。
- 桥梁工程 /
- 拱桥 /
- 超载 /
- 随机车队 /
- 荷载效应 /
- 荷载标准
Abstract: The influence of current overload vehicles on bridge and the applicability of vehicle design load standard in General Specifications for Design of Highway Bridges and Culverts (JTG D60—2015) to the operating vehicle load on highway were analyzed.The weigh-in-motion (WIM) measured data of vehicle loads on Guangshen Expressway were studied.The Monte Carlo method was used to simulate the random load and random spacing of vehicle, the loading effect of random fleet was programmed, and the bending moment effects of clamped arch bridge sections at the midspan and arch foot were calculated.Based on the maximum value distribution principle, the characteristic values of loading effect in the design reference period were obtained, the standard model of recommended vehicle load based on the WIM measured data was presented, and the recommended load standard was compared with the design load standard in the current code (JTG D60—2015).Calculation result shows that the effect of recommended vehicle loadstandard is well applicative and inclusive to the measured values, the errors of bending moment at the midspan are less than 7%, the errors at the arch foot are 5%-11% when bridge spans are 25-65, 110 and 120 m, and the others are less than 5%.The ratios of generated bending moment effects resulting from the putative load standard based on the measured values of Guangshen Expressway and the highway I-grade lane load of current code on the clamped arch bridge are1.24-2.18, and the average ratio is 1.80, which indicates that the traffic of Guangshen Expressway is heavy, vehicle overloading is serious, and the load standard in the current code has great deviation with the deductive load standard according to the measured vehicle load of Guangshen Expressway, so the bridge design load standard of Guangshen Expressway should properly increase based on the existing standard.
- bridge engineering /
- arch bridge /
- overload /
- random vehicle queue /
- load effect /
- load standard

HTML全文

图 1 车道

Figure 1. Vehicle lanes

下载: 全尺寸图片幻灯片

图 2 车辆总质量概率密度函数

Figure 2. Probability density function of vehicle total mass

下载: 全尺寸图片幻灯片

图 3 随机车队

Figure 3. Random vehicle queue

下载: 全尺寸图片幻灯片

图 4 荷载效应计算流程

Figure 4. Computation flowchart of load effect

下载: 全尺寸图片幻灯片

图 5 弯矩效应概率密度函数

Figure 5. Probability density functions of moment effects

下载: 全尺寸图片幻灯片

图 6 P-L曲线

Figure 6. P-Lcurves

下载: 全尺寸图片幻灯片

图 7 效应比值

Figure 7. Effect ratios

下载: 全尺寸图片幻灯片

表 1 车型比例

Table 1. Vehicle type proportions

下载: 导出CSV

表 2 车辆总质量统计参数

Table 2. Statistic parameters of vehicle total mass

下载: 导出CSV

表 3 车辆总质量分布和轴重与总质量的比例

Table 3. Distributions of total masses and ratios of axle weights to total masses for vehicles

下载: 导出CSV

表 4 设计基准期车辆荷载与轴重

Table 4. Vehicle loads and axle weights in design reference period

下载: 导出CSV

表 5 跨中弯矩效应分布参数与标准值

Table 5. Distribution parameters and characteristic values of midspan moment effects

下载: 导出CSV

表 6 拱脚弯矩效应分布参数与标准值

Table 6. Distribution parameters and characteristic values of arch-foot moment effects

下载: 导出CSV

表 7 集中力参数

Table 7. Parameters of concentrated forces

下载: 导出CSV

表 8 建议设计荷载与规范设计荷载效应比值

Table 8. Effect ratios of proposed design loads and current codes'design loads

下载: 导出CSV

参考文献(26)

[1]	FU Gong-kang, YOU Ji. Extrapolation for future maximum load statistics[J]. Journal of Bridge Engineering, 2011, 16 (4): 527-535. doi: 10.1061/(ASCE)BE.1943-5592.0000175
[2]	OBRIEN E J, ENRIGHT B. Using weigh-in-motion data to determine aggressiveness of traffic for bridge loading[J]. Journal of Bridge Engineering, 2013, 18 (3): 232-239. doi: 10.1061/(ASCE)BE.1943-5592.0000368
[3]	HU Da-lin, DING Ding, CHEN Long-gang, et al. Research on design vehicle load for long-span bridges[J]. Applied Mechanics and Materials, 2011, 90-93: 909-914. doi: 10.4028/www.scientific.net/AMM.90-93.909
[4]	党栋, 贺拴海, 周勇军, 等. 基于车辆统计数据的汽车荷载标准值取值与评估[J]. 长安大学学报: 自然科学版, 2012, 32 (6): 44-51. doi: 10.3969/j.issn.1671-8879.2012.06.008 DANG Dong, HE Shuan-hai, ZHOU Yong-jun, et al. Choosing and assessment for the standard of vehicle load based on vehicle statistical data[J]. Journal of Chang'an University: Natural Science Edition, 2012, 32 (6): 44-51. (in Chinese). doi: 10.3969/j.issn.1671-8879.2012.06.008
[5]	MORALES-NÁPOLES O, STEENBERGEN R D J M. Analysis of axle and vehicle load properties through Bayesian networks based on weigh-in-motion data[J]. Reliability Engineering and System Safety, 2014, 125 (7): 153-164.
[6]	夏叶飞, 李峰峰, 顾煜, 等. 基于WIM的高速公路桥梁车辆疲劳荷载谱研究[J]. 公路交通科技, 2014, 31 (3): 56-64. https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201403010.htm XIA Ye-fei, LI Feng-feng, GU Yu, et al. Study on vehicular fatigue load spectrum expressway bridge based on WIM system[J]. Journal of Highway and Transportation Research and Development, 2014, 31 (3): 56-64. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201403010.htm
[7]	卢九章. 基于WIM的北京市G103国道车辆荷载模型研究[J]. 市政技术, 2015, 33 (2): 58-62. https://www.cnki.com.cn/Article/CJFDTOTAL-SZJI201502022.htm LU Jiu-zhang. Research on WIM based vehicle load model of national highway G103in Beijing[J]. Municipal Engineering Technology, 2015, 33 (2): 58-62. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-SZJI201502022.htm
[8]	杜江. 基于WIM的高速公路车辆荷载分析[D]. 大连: 大连海事大学, 2016. DU Jiang. Analysis of highway vehicle load based on WIM[D]. Dalian: Dalian Maritime University, 2016. (in Chinese).
[9]	梁栋, 董春霞, 赵少伟, 等. 适用于重载交通的公路桥梁荷载标准研究[J]. 公路, 2011 (3): 30-36. https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201103008.htm LIANG Dong, DONG Chun-xia, ZHAO Shao-wei, et al. Research on load standard of highway bridges suitable for heavy load traffic[J]. Highway, 2011 (3): 30-35. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201103008.htm
[10]	刘浪, 尤吉. 公路桥梁车辆荷载效应的外推计算[J]. 土木工程学报, 2015, 48 (4): 59-64. https://www.cnki.com.cn/Article/CJFDTOTAL-TMGC201504011.htm LIU Lang, YOU Ji. Extrapolation method for truck load effects on highway bridges[J]. China Civil Engineering Journal, 2015, 48 (4): 59-64. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-TMGC201504011.htm
[11]	宗周红, 李峰峰, 夏叶飞, 等. 基于WIM的新沂河大桥车辆荷载模型研究[J]. 桥梁建设, 2013, 43 (5): 29-36. https://www.cnki.com.cn/Article/CJFDTOTAL-QLJS201305006.htm ZONG Zhou-hong, LI Feng-feng, XIA Ye-fei, et al. Study of vehicle load models for Xinyi River Bridge based on WIM data[J]. Bridge Construction, 2013, 43 (5): 29-36. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-QLJS201305006.htm
[12]	郝志强. 重载交通路段桥梁荷载效应的分析与研究[J]. 公路, 2015 (2): 111-115. https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201502025.htm HAO Zhi-qiang. Analysis and research of heavy traffic road bridge load effect[J]. Highway, 2015 (2): 111-115. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201502025.htm
[13]	蒋田勇, 谢静思. 高速公路桥梁随机荷载分布特性研究[J]. 公路交通科技, 2015, 32 (7): 76-83, 91. https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201507014.htm JIANG Tian-yong, XIE Jing-si. Investigation on distribution characteristics of random loads on expressway bridge[J]. Journal of Highway and Transportation Research and Development, 2015, 32 (7): 76-83, 91. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201507014.htm
[14]	宇德忠, 杨洪生, 程培峰. 黑龙江省高等级公路轴载分布规律的研究[J]. 公路, 2015 (3): 120-125. https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201503027.htm YU De-zhong, YANG Hong-sheng, CHENG Pei-feng. Research on the laws of typical axial load distribution of high class highway in Heilongjiang Province[J]. Highway, 2015 (3): 120-125. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLGL201503027.htm
[15]	胡超. 重载交通公路桥梁设计荷载标准研究[D]. 天津: 河北工业大学, 2015. HU Chao. Study on highway bridge vehicle loads of heavy load traffic[D]. Tianjing: Hebei University of Technology, 2015. (in Chinese).
[16]	刘国军, 魏召兰, 杨永清. 城市桥梁汽车荷载调查与疲劳荷载模型研究[J]. 公路交通科技, 2014, 31 (6): 86-93. https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201406013.htm LIU Guo-jun, WEI Zhao-lan, YANG Yong-qing. Research on vehicular loads and fatigue load model of urban road bridge[J]. Journal of Highway and Transportation Research and Development, 2014, 31 (6): 86-93. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-GLJK201406013.htm
[17]	陈斌, 钟先群, 谢旭, 等. 基于WIM的城市桥梁车辆荷载概率模型[J]. 地震工程与工程振动, 2014 (增1): 686-691. https://www.cnki.com.cn/Article/CJFDTOTAL-DGGC2014S1108.htm CHEN Bin, ZHONG Xian-qun, XIE Xu, et al. WIM based vehicle load model for urban expressway bridges[J]. Earthquake Engineering and Engineering Dynamics, 2014 (S1): 686-691. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-DGGC2014S1108.htm
[18]	杨琪, 黄建跃, 阮欣, 等. 基于WIM数据的桥梁实际汽车荷载效应的研究[J]. 公路工程, 2010, 35 (4): 15-18. https://www.cnki.com.cn/Article/CJFDTOTAL-ZNGL201004003.htm YANG Qi, HUANG Jian-yue, RUAN Xin, et al. Study of the actual vehicle load effect of bridges base on WIM data[J]. Highway Engineering, 2010, 35 (4): 15-18. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-ZNGL201004003.htm
[19]	黎明. 超载运营对在役钢筋混凝土梁(板) 式桥梁安全性影响研究[D]. 兰州: 兰州交通大学, 2014. LI Ming. The safety influence study of overload operation to existing reinforced concrete beam (slab) bridges structure[D]. Lanzhou: Lanzhou Jiaotong University, 2014. (in Chinese).
[20]	刘扬, 张海萍, 鲁乃唯, 等. 基于WIM的随机车流建模和简支梁桥荷载效应研究[J]. 桥梁建设, 2015, 45 (5): 13-18. https://www.cnki.com.cn/Article/CJFDTOTAL-QLJS201505003.htm LIU Yang, ZHANG Hai-ping, LU Nai-wei, et al. Study of random vehical flow modeling and load effect of simplysupported beam bridge based on WIM data[J]. Bridge Construction, 2015, 45 (5): 13-18. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-QLJS201505003.htm
[21]	夏坚, 宗周红, 杨泽刚, 等. 基于GPS的大跨斜拉桥车辆荷载模型[J]. 中国公路学报, 2016, 29 (1): 44-52. https://www.cnki.com.cn/Article/CJFDTOTAL-ZGGL201601007.htm XIA Jian, ZONG Zhou-hong, YANG Ze-gang, et al. Vehicle load model of large-span cable-stayed bridge based on GPS[J]. China Journal of Highway and Transport, 2016, 29 (1): 44-52. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-ZGGL201601007.htm
[22]	杨东晓, 张俊平, 黄海云, 等. 运营车辆荷载发展变异及其对中小跨径拱桥受力影响的模拟分析[J]. 中国科技论文, 2015, 10 (7): 808-811, 828. https://www.cnki.com.cn/Article/CJFDTOTAL-ZKZX201507013.htm YANG Dong-xiao, ZHANG Jun-ping, HUANG Hai-yun, et al. The development variations of operating vehicle load and the numerical simulation of its impact on medium and small span arch bridge[J]. China Sciencepaper, 2015, 10 (7): 808-811, 828. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-ZKZX201507013.htm
[23]	HU Da-lin, CHEN Long-gang, DING Ding, et al. Analysis of vehicle loads on Guangzhou-Shenzhen Expressway[J]. Applied Mechanics and Materials, 2011, 90-93: 915-920.
[24]	O'CONNOR A, O'BRIEN E J. Traffic load modelling and factors influencing the accuracy of predicted extremes[J]. Canadian Journal of Civil Engineering, 2005, 32 (1): 270-278.
[25]	MIAO Tian-jun. Bridge live load models with special reference to Hong Kong[D]. Hong Kong: Hong Kong Polytechnic University, 2001.
[26]	夏樟华, 陈俊民, 宗周红, 等. 并道运行状态下高速公路桥梁车辆荷载效应[J]. 长安大学学报: 自然科学版, 2017, 37 (1): 76-84. https://www.cnki.com.cn/Article/CJFDTOTAL-XAGL201701010.htm XIA Zhang-hua, CHEN Jun-min, ZONG Zhou-hong, et al. Vehicle load effect of expressway bridge in the state of lanes merging[J]. Journal of Chang'an University: Natural Science Edition, 2017, 37 (1): 76-84. (in Chinese). https://www.cnki.com.cn/Article/CJFDTOTAL-XAGL201701010.htm