-
摘要: 分析了ECE制动法规对多轴汽车制动力分配的要求, 指出目前多轴汽车制动性能分析方法的不足, 提出了基于ECE制动法规的利用附着系数图示法。在同一坐标系中画出汽车各轴的利用附着系数曲线和ECE制动法规边界曲线, 通过分析各轴利用附着系数之间的位置关系及其与边界曲线之间的关系来研究汽车的制动性能。考虑到多轴汽车制动时轴荷转移较大的实际工况, 在计算车轮地面法向反力时, 采用簧上动载荷和簧下载荷分开计算模型。分析结果表明: 当利用附着系数为0.20~0.80时, 汽车具有较高的附着利用率; 当制动强度为0.15~0.30时, 车轮抱死顺序为前、中、后, 符合车轮抱死顺序要求, 能够保证汽车制动时的方向稳定性。可见, 该分析方法简单、实用。Abstract: According to ECE brabing regulation, the requirements of braking force distribution of multi-axle automobile were analyzed, the defects of analysis methods on the braking performance of multi-axle automobile were pointed out, and a method named adhesion utilization coefficient diagram was proposed. The adhesion utilization curves of all axles and the boundary curves requested by ECE braking regulation were painted in the same coordinate system, the relationships among the adhesion utilization coefficients and the boundary curves, and the braking performance of automobile were studied. Because the transfer of multi-axle automobile' vertical axle loads was larger when braking, when calculating the normal reaction forces from ground to wheels, a model was adopted, in which the loads on and below suspension were calculated separately. An example was cited to illustrate the application of the analysis method. The result indicates that when adhesion utilization coefficient is from 0.20 to 0.80, automobile has a high adhesion utilization efficiency. When braking strength is from 0.15 to 0.30, wheel lock sequence is front, middle and rear, which accords with wheel lock requirements, and the directional stability of automobile is guaranteed when braking. Obviously, the method is simple, practical and beneficial.
-
表 1 整车参数
Table 1. Vehicle parameters
参数 空载 满载 汽车总质量/kg 9 600 14 600 悬挂质心离前轴距离/mm 1 807 2 601 悬挂质心高度/mm 1 163 1 353 非悬挂质量/kg 前轴为920, 中轴为900, 后轴为900 制动力分配系数 β1为0.546, β2为0.273, β3为0.181 
下载: 导出CSV
-
[1] 徐安, 乔向明. 公路客运安全分析与车辆制动性能建模[J]. 交通运输工程学报, 2009, 9 (6): 87-91. http://transport.chd.edu.cn/article/id/200906017XU An, QIAO Xiang-ming. Safety analysis of highway passengertransport and modeling of vehicle brake performances[J]. Journal of Traffic and Transportation Engineering, 2009, 9 (6): 87-91. (in Chinese) http://transport.chd.edu.cn/article/id/200906017 [2] 宋年秀, 苏建, 王东杰, 等. 半挂汽车列车弯道行驶制动稳定性[J]. 交通运输工程学报, 2010, 10 (1): 50-55. http://transport.chd.edu.cn/article/id/201001009SONG Nian-xiu, SU Jian, WANG Dong-jie, et al. Brakingstability of tractor-semitrailer running on curve[J]. Journalof Traffic and Transportation Engineering, 2010, 10 (1): 50-55. (in Chinese) http://transport.chd.edu.cn/article/id/201001009 [3] 张立军, 朱博, 贾云雷. 依ECE法规进行汽车制动力分配新方法[J]. 辽宁工程技术大学学报: 自然科学版, 2005, 24 (2): 276-279. https://www.cnki.com.cn/Article/CJFDTOTAL-FXKY200502040.htmZHANG Li-jun, ZHU Bo, JI A Yun-lei. New method forbraking force distribution of automobile according to ECEregulation[J]. Journal of Liaoning Technical University: Natural Science, 2005, 24 (2): 276-279. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-FXKY200502040.htm [4] 汪文国. 多轴汽车制动性能的简易分析法[J]. 机械科学与技术, 1996, 25 (1): 9-11. https://www.cnki.com.cn/Article/CJFDTOTAL-JXZZ199601001.htmWANG Wen-guo. Brief analysis of braking performance ofmulti-axle automobile[J]. Mechanical Science and Technology, 1996, 25 (1): 9-11. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JXZZ199601001.htm [5] 汪文国. 半挂汽车列车制动稳定性分析方法探讨[J]. 机械研究与应用, 1996 (4): 9-12. https://www.cnki.com.cn/Article/CJFDTOTAL-JXYJ604.002.htmWANG Wen-guo. Investigation on design methodfor brakingstability of half-trailer automobile train[J]. MechanicalResearch and Application, 1996 (4): 9-12. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JXYJ604.002.htm [6] ECE R-13, uniform provisions concerning the approval ofvehicles of categories M, Nand O with regard to braking[S]. [7] 汪之望, 钱友军, 郭春雷. 中卡三轴载货车制动系统的匹配设计[J]. 合肥工业大学学报: 自然科学版, 2007, 30 (增): 16-18, 55. https://www.cnki.com.cn/Article/CJFDTOTAL-HEFE2007S1003.htmWANG Zhi-wang, QIAN You-jun, GUO Chun-lei. The matchdesign of braking system for a tri-axial mid-sized-truck[J]. Journal of Hefei University of Technology: Natural Science, 2007, 30 (S): 16-18, 55. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-HEFE2007S1003.htm [8] 王国军, 陈欣, 徐安桃, 等. 多轴汽车轴荷的合理分配与确定[J]. 军事交通学院学报, 2009, 11 (2): 53-56.WANG Guo-jun, CHEN Xin, XU An-tao, et al. Reasonable distribution and calculation of the axle load for multi-axlevehicles[J]. Journal of Academy of Military Transportation, 2009, 11 (2): 53-56. (in Chinese) [9] 王兴东, 杨波, 邹光明. 多轴汽车轴荷分配和转移的计算方法研究[J]. 湖北工业大学学报, 2006, 21 (3): 165-167. https://www.cnki.com.cn/Article/CJFDTOTAL-HBGX200603056.htmWANG Xing-dong, YANG Bo, ZOU Guang-ming. Computing methods for distribution and transfer of multi-axle vehiclesvertical axle loads[J]. Journal of Hubei University ofTechnology, 2006, 21 (3): 165-167. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-HBGX200603056.htm [10] 柴新伟, 杨世文. 三轴汽车轴荷计算及轴距选择[J]. 机械管理开发, 2010, 25 (1): 53-54, 56. https://www.cnki.com.cn/Article/CJFDTOTAL-JSGL201001028.htmCHAI Xin-wei, YANG Shi-wen. The axle loads calculationsof three-axle vehicle and upgraded wheelbase[J]. Mechanical Management and Development, 2010, 25 (1): 53-54, 56. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JSGL201001028.htm [11] 赵伟, 魏朗, 杜峰. 基于横摆力矩的汽车制动稳定性模糊控制[J]. 长安大学学报: 自然科学版, 2008, 28 (6): 76-80. https://www.cnki.com.cn/Article/CJFDTOTAL-XAGL200806021.htmZHAO Wei, WEI Lang, DU Feng. Fuzzy control of automobile braking stability based on yaw moment control[J]. Journal ofChang an University: Natural Science Edition, 2008, 28 (6): 76-80. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-XAGL200806021.htm [12] 吴晓东, 李冰, 赵学增. 基于制动轨迹检测的汽车路试模拟技术[J]. 中国公路学报, 2008, 21 (1): 111-115. https://www.cnki.com.cn/Article/CJFDTOTAL-ZGGL200801021.htmWU Xiao-dong, LI Bing, ZHAO Xue-zeng. Roadtest simulation technology of automobile based on brake trajectory test[J]. China Journal of Highway and Transport, 2008, 21 (1): 111-115. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-ZGGL200801021.htm -
点击查看大图
图(3) / 表(1)
计量
- 文章访问数: 778
- HTML全文浏览量: 105
- PDF下载量: 608
- 被引次数: 0
