Simulation and optimization design on cylindrical pleated lube oil filter
Article Text (Baidu Translation)
-
摘要: 为降低机油滤清器过滤压力损失, 通过压力损失试验, 确定了压力损失模拟的边界条件, 建立了压力损失的二维CFD模拟模型, 分析了压力损失特性与影响因素, 推导了压力损失与影响因素的多元回归关系式。模拟结果表明: 对滤芯压降影响的主次顺序为过滤速度、滤芯折高、流道宽度、折数、滤纸厚度与含尘浓度; 滤芯初始压力损失与其结构及运行参数呈非线性关系, 并与滤芯褶数存在最佳值; 回归关系式的相关系数为0.998, 因此, 可靠性高。
-
关键词:
- 圆筒状褶式机油滤清器 /
- 过滤压力损失 /
- CFD数值模拟 /
- 优化设计
Abstract: In order to reduce the pressure drop of lube oil filter, the boundary simulation conditions of the pressure drop were confirmed by pressure drop test, and a 2D CFD(computational fluid dynamics) simulation model was put forward.The properties of the pressure drop and its influence factors were analyzed, and a multianalysis regress relationship was proposed.Simulation result shows that the influence factors are filtrating speed, fold height, routeway width, fold number, filter paper thickness and impurity concentration, whose influence degrees are from big to small.The relationships between the initial pressure drop and the influence factors but the thickness are nonlinear, besides, there is an optimal fold number.The correlative coefficient of the regress relationship is 0.998, so the relationship is credible. -
表 1 模拟计算、公式计算和试验结果比较
Table 1. Comparison of simulation, calculation and experiment results
下载: 导出CSV
-
[1] ⅢYTJO Ó E, 任广宇. 内燃机车柴油机的离心式机油滤清器[J]. 国外内燃机车, 1999(5): 34-37. https://www.cnki.com.cn/Article/CJFDTOTAL-GWMJ199905006.htmⅢYTJOÓA E, REN Guang-yu. Centrifugal lube oil filter ofdiesel engine for diesel locomotive[J]. Foreign Diesel Loco-motive, 1999(5): 34-37. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-GWMJ199905006.htm [2] 李大鸣, 张红萍, 李冰绯, 等. 多孔介质内部流动模型及其数学模拟[J]. 天津大学学报, 2002, 35(6): 699-704. doi: 10.3969/j.issn.0493-2137.2002.06.006LI Da-ming, ZHANG Hong-ping, LI Bing-fei, et al. Flowingmodel and mathematical si mulations in porous medium[J]. Journal of Tianjin University, 2002, 35(6): 699-704. (in Chinese) doi: 10.3969/j.issn.0493-2137.2002.06.006 [3] DEL FABBRO L, BRUN P, LABORDEJ C, et al. Study ofthe clogging of industrial pleated filters by solid particles[J]. Journal of Aerosol Science, 2000, 31(SUP1): 210-211. [4] DEL FABBRO L, LABORDE J C, MERLI N P, et al. Airflows and pressure drop modeling for different pleatedindustrial filters[J]. Filtration and Separation, 2002, 39(1): 35-40. [5] YANGJuan, STEWART M, MAUPI N G, et al. Single walldiesel particulate filter(DPF)filtration efficiency studies usinglaboratory generated particles[J]. Chemical Engineering Science, 2009, 64(8): 1625-1634. doi: 10.1016/j.ces.2008.12.011 [6] CAESAR T, SCHROTH T. Theinfluence of pleat geometryon the pressure drop in deep-pleated cassette filters[J]. Filtration and Separation, 2002, 39(9): 49-54. [7] LUCKE T, FISSAN H. The prediction of filtration performanceof high efficiency gas filter elements[J]. Chemical EngineeringScience, 1996, 51(8): 1199-1208. [8] SUBRENAT A, BELLETTRE J, LE CLOIREC P. 3-Dnumerical si mulations of flows in a cylindrical pleated filterpacked with activated carbon cloth[J]. Chemical EngineeringScience, 2003, 58(22): 4965-4973. [9] BALEO J N, SUBRENAT A, LE CLOIREC P. Numericalsi mulation of flows in air treat ment devices using activatedcarbon cloths filters[J]. Chemical Engineering Science, 2000, 55(10): 1807-1816. doi: 10.1016/S0009-2509(99)00441-8 [10] FAN Long, MAO Zai-sha, WANG Yun-dong. Numericalsi mulation of turbulent solid-liquid two-phase flow andorientation of slender particles in a stirred tank[J]. ChemicalEngineering Science, 2005, 60(24): 7045-7056. [11] CAOJ, AHMADI G. Gas-particle two-phase turbulent flowin a vertical dust[J]. International Journal of MultiphaseFlow, 1995, 21(6): 1203-1228. doi: 10.1016/0301-9322(95)00042-V -
图(12) / 表(1)
计量
- 文章访问数: 625
- HTML全文浏览量: 222
- PDF下载量: 605
- 被引次数: 0
