-
摘要: 针对国内400 km·h-1变轨距动车组转向架的研发和设计问题，在借鉴国外成熟变轨距转向架技术的基础上，重点研究了国内高速变轨距动车组转向架的5个关键问题，即牵引电机布置方式、轮对驱动方式、轴箱轴承、变轨机构、基础制动及撒砂装置，对研究中发现的问题提出了相应的解决措施。研究结果表明：电机架悬和体悬都可以给制动盘的安装让出空间，但是电机与所驱动的车轴之间都会产生相对位移，需要采取运动补偿措施；为了满足400 km·h-1变轨距动车组车轴尺寸和转速要求，需研发新型轴箱轴承；变轨机构的存在会使转向架簧下质量增大，所以研制的变轨距转向架应尽量采用轻量化设计；考虑到制动效率和夹钳随动问题对变轨距转向架制动效果的影响，基础制动应优先采用轴盘制动，其次为轮盘制动；动车组转向架尽量不采用撒砂装置，若非用不可，考虑在砂箱和喷砂嘴之间采用软管连接，以适应变轨距时的运动补偿；在对变轨距转向架进行研发的同时，应注意地面变轨设施的广泛使用，使之达到简统化、标准化的要求；变轨距转向架的研制必须考虑不同轨距铁路的限界要求，轨距相差越大，对限界要求也就越高。所研发的动车组整车于西南交通大学滚振试验台上，在施加中国客运专线线路谱激扰的情况下，最高运行速度达到了602 km·h-1，并于2020年10月21日成功下线。Abstract: To address the problems in the development and design of 400 km·h-1 variable gauge EMUs bogies in China, five important problems for Chinese high-speed variable gauge EMUs bogies (i.e., traction motor mounting, type of wheel set drive, axle box bearing, track changing mechanism, foundation brake, and sanding device) were studied based on the mature variable gauge bogie technologies developed in other countries. Corresponding solutions to the problems discovered in this study were also proposed. Research result shows that both the electric motor suspension and body suspension can make room for the installation of brake disc, but those will be relative displacements between the motor and the driven axles, which requires motion compensation measures. To meet the requirements of axle size and rotating speed of 400 km·h-1 variable gauge EMUs, it is necessary to develop new axle box bearings. The existence of track changing mechanism will increase the unsprung mass of bogie, so the developed variable gauge bogie should adopt a lightweight design as much as possible. Considering the effects of braking efficiency and caliper follow-up on the braking effect of variable gauge bogie, the basic braking should be given priority to the axle disc braking, followed by the wheel disc braking. Sanding device shall not be used for bogie of EMU, if it is absolutely necessary, considering using a hose connection between the sandbox and the sandblasting nozzle to adapt to the motion compensation when the gauge changes. While researching and developing the variable gauge bogie, attention should be paid to the wide use of ground track changing device, so that they can also meet the requirements of simplicity and standardization. The development of variable gauge bogie must consider the clearance requirements of different gauge railways, the greater the gauge difference, the higher the clearance requirement. On the rolling vibration test-bed of Southwest Jiaotong University, the maximum running speed of the developed EMU reaches 602 km·h-1 under the condition of applying line spectrum excitation of Chinese passenger dedicated line and it was successfully launched in October 21, 2020. 2 tabs, 10 figs, 36 refs.
-
Key words:
- EMUs /
- variable gauge bogie /
- axle box bearing /
- ground track changing device /
- motor suspension mode /
- clearance
-
图 3 DB AG/Rafil Type V变轨距转向架轮对结构
Figure 3. Wheelset structure of variable gauge bogie of DB AG/Rafil Type V
图 4 E30A和E30B变轨距转向架轮对结构
Figure 4. Wheelset structures of E30A and E30B variable gauge bogies
图 6 轴承类型、润滑情况与其转速的关系
Figure 6. Relationship among bearing type, lubrication and rotating speed
图 7 德国变轨距轮对的锁紧/解锁机构
Figure 7. Locking/unlocking mechanism of variable gauge wheelset in Germany
图 8 E30B型变轨距转向架锁紧/解锁机构
Figure 8. Locking/unlocking mechanism of E30B variable gauge bogies
图 9 日本第三代变轨距转向架轮对结构
Figure 9. Wheelset structure of third generation variable gauge bogies in Japan
图 10 国外典型变轨距转向架地面变轨设施
Figure 10. Foreign typical ground track changing device for variable gauge bogies
表 1 各国变轨距转向架特点对比
Table 1. Comparison of characteristics of variable gauge bogies in different countries
国家名称 变轨距转向架名称 运行轨距/mm 轮对旋转方式 最高运行速度/(km·h-1) 适用车型 主要特点 西班牙 Talgo RD 1 668/1 435 独立式 260 客/货 轮对由2个半轴组成，车轮独立旋转，锁紧机构安装于短车轴 CAF BRAVA 1 668/1 435 独立式 250 客 扭矩的传递不通过车轴，车轴不旋转，齿轮箱通过万向轴与体悬电机相连 波兰 SUW2000 1 520/1 435
1 668/1 435
1 668/1 520/1 435整体式 200 客/货 车轮采用整体式旋转，依靠与车轴一体的固定套筒和轮毂加长区域的对插结构传递扭矩 德国 DB AG/Rafil Type V 1 524/1 435 整体式 160 货 锁紧机构设计在车轮轮毂处，左右车轮以整体式旋转，设计速度较低 日本 E30A 1 435/1 067 独立式 210 客 采用独立旋转车轮，牵引电机采用外转子式，转子和车轮直接相连来传递扭矩 E30B 1 435/1 067 整体式 210 客 采用整体式旋转车轮，曲线通过性能良好，牵引电机架悬，采用平行万向轴驱动方式并用滚子花键传递扭矩 
下载: 导出CSV
表 2 几款标准轴承相关参数
Table 2. Relevant parameters of several standard bearings
轴承类型 轴承型号 轴承内径/mm 轴承外径/mm 轴承宽度/mm 额定载荷/kN 极限载荷/kN 参考转速/(r·min-1) 极限转速/(r·min-1) 圆柱滚子轴承 NJ 238 ECML 190 340 55 800 965 2 000 3 400 圆柱滚子轴承 NJ 238 ECM 190 340 55 800 965 2 000 2 000 圆柱滚子轴承 NUP 238 ECML 190 340 55 800 965 2 000 3 400 圆柱滚子轴承 NUP 238 ECM 190 340 55 800 965 2 000 2 000 圆柱滚子轴承 NU 2238 ECML 190 340 92 1 220 1 600 2 000 3 400 圆柱滚子轴承 NU 2238 ECM 190 340 92 1 220 1 600 2 000 2 000
下载: 导出CSV
-
[1] 金万建. 我国铁路开展国际联运及国际通道的发展[J]. 铁道运输与经济, 2003, 25(3): 4-8. doi: 10.3969/j.issn.1003-1421.2003.03.003JIN Wan-jian. The international corridor transportation implemented by Chinese railway and the development of international corridor[J]. Railway Transport and Economy, 2003, 25(3): 4-8. (in Chinese) doi: 10.3969/j.issn.1003-1421.2003.03.003 [2] 徐彬, 黄志辉, 舒友, 等. 变轨距转向架研制与应用思考[J]. 机车电传动, 2018, 262(3): 14-17. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201803002.htmXU Bin, HUANG Zhi-hui, SHU You, et al. Development and application strategy of gauge-changeable bogies[J]. Electric Drive for Locomotives, 2018, 262(3): 14-17. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201803002.htm [3] 李芾, 邵亚堂, 黄运华, 等. 国外变轨距列车及其转向架的发展与研究[J]. 机车电传动, 2018, 262(3): 1-13. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201803001.htmLI Fu, SHAO Ya-tang, HUANG Yun-hua, et al. Development and research of foreign gauge-changeable train and bogie[J]. Electric Drive for Locomotives, 2018, 262(3): 1-13. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201803001.htm [4] NETZEL A. Derautomatisch umspurbare HGV-Triebzug Talgo 250[J]. ZEV Rail Glasers Annalen, 2008, 132: 170-171. http://cat.inist.fr/?aModele=afficheN&cpsidt=20940983 [5] SALIGER W. Gauge-adjustable wheelsets[J]. Rail Internation, 2000, 31(5): 7-13. http://www.researchgate.net/publication/294098812_Gauge-adjustable_wheelsets [6] WILHELM S. 可调轨距轮对[J]. 国外内燃机车, 2002, 362(2): 28-33. https://www.cnki.com.cn/Article/CJFDTOTAL-GWMJ200202009.htmWILHELM S. Adjustable gauge wheelset[J]. Foreign Diesel Locomotives, 2002, 362(2): 28-33. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-GWMJ200202009.htm [7] 范燕. 可变轨距货车轮对[J]. 国外铁道车辆, 2000, 37(4): 45. https://www.cnki.com.cn/Article/CJFDTOTAL-GWTD200004016.htmFAN Yan. Variable gauge freight wheelsets[J]. Foreign Rolling Stock, 2000, 37(4): 45. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-GWTD200004016.htm [8] NORIAKI T, 周贤全. 可变轨距转向架的开发[J]. 国外铁道车辆, 2006, 43(1): 27-31. doi: 10.3969/j.issn.1002-7610.2006.01.006NORIAKI T, ZHOU Xian-quan. Development of variable gauge bogies[J]. Foreign Rolling Stock, 2006, 43(1): 27-31. (in Chinese) doi: 10.3969/j.issn.1002-7610.2006.01.006 [9] GYR C, DEISS C, FORCLAZ J M. Development of a gauge-changing trailer bogie (type EV09)[J]. Research Gate, 2011, 135: 130-139. http://www.researchgate.net/publication/292907541_Development_of_a_gauge-changing_trailer_bogie_type_EV09 [10] CHRISTOPH G, CHRISTOPH D, JEAN M F. Entwicklung eines spurwechselfähigen Laufdrehgestells (type EV09)[J]. ZEV Rail Glasers Annalen, 2011, 135: 130-139. http://cat.inist.fr/?amodele=affichen&cpsidt=24766617 [11] KIM C S, CHANG C S, JANG S H, et al. Structural analysis of locking parts in the gauge-adjustable wheelset[J]. Journal of the Korean Society for Railway, 2008, 11(1): 33-38. http://www.researchgate.net/publication/263999733_Structural_Analysis_of_Locking_Parts_in_the_Gauge_-Adjustable_Wheelset [12] 黄运华, 李芾. 铁道车辆轮对变轨距技术研究[J]. 铁道车辆, 2002, 40(7): 8-11. doi: 10.3969/j.issn.1002-7602.2002.07.003HUANG Yun-hua, LI Fu. Research on gauge changing technology of railway vehicle wheelset[J]. Rolling Stock, 2002, 40(7): 8-11. (in Chinese) doi: 10.3969/j.issn.1002-7602.2002.07.003 [13] 刘寅华, 李芾, 黄运华. 铁道货车变轨距轮对结构方案设计[J]. 铁道机车车辆, 2006, 26(6): 13-15. doi: 10.3969/j.issn.1008-7842.2006.06.005LIU Yin-hua, LI Fu, HUANG Yun-hua. Structure scheme of gauge-changeable wheelsets for freight car[J]. Railway Locomotive and Car, 2006, 26(6): 13-15. (in Chinese) doi: 10.3969/j.issn.1008-7842.2006.06.005 [14] 张良威, 李芾, 黄运华. 变轨距转向架锁紧机构方案设计[J]. 铁道机车车辆, 2007, 27(5): 6-8. doi: 10.3969/j.issn.1008-7842.2007.05.003ZHANG Liang-wei, LI Fu, HUANG Yun-hua. Scheme design of locking mechanism of gauge-changeable bogie[J]. Railway Locomotive and Car, 2007, 27(5): 6-8. (in Chinese) doi: 10.3969/j.issn.1008-7842.2007.05.003 [15] 崔红伟, 黄志辉, 周殿买, 等. 1 435/1 000 mm变轨距转向架轮对轴箱设计[J]. 机车电传动, 2018, 264(5): 9-12. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805003.htmCUI Hong-wei, HUANG Zhi-hui, ZHOU Dian-mai, et al. Design of wheelset axle box for 1 435/1 000 mm gauge-changeable bogie[J]. Electric Drive for Locomotives, 2018, 264(5): 9-12. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805003.htm [16] 邵亚堂, 黄运华, 张隶新, 等. 变轨距列车用地面变轨设施方案设计[J]. 机车电传动, 2018, 263(4): 10-14. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804004.htmSHAO Ya-tang, HUANG Yun-hua, ZHANG Li-xin, et al. Scheme design of ground transformation facility for gauge-changeable trains[J]. Electric Drive for Locomotives, 2018, 263(4): 10-14. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804004.htm [17] 史炎, 何健. 钓竿式变轨距转向架动力学研究[J]. 铁道机车车辆, 2018, 38(1): 7-9. doi: 10.3969/j.issn.1008-7842.2018.01.02SHI Yan, HE Jian. Design and dynamics of fishing rod gauge-changeable bogie[J]. Railway Locomotive and Car, 2018, 38(1): 7-9. (in Chinese) doi: 10.3969/j.issn.1008-7842.2018.01.02 [18] 李涛. 高速变轨距转向架设计及动力学性能研究[D]. 成都: 西南交通大学, 2018.LI Tao. Research on design and dynamics performance of high-speed gauge changeable bogie[D]. Chengdu: Southwest Jiaotong University, 2018. (in Chinese) [19] 韩光旭, 周殿买, 黄志辉. 高速变轨距转向架轴箱轴承选型及寿命评估[J]. 机车电传动, 2018, 263(4): 6-9. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804003.htmHAN Guang-xu, ZHOU Dian-mai, HUANG Zhi-hui. Type selection and life assessment of high-speed gauge-changeable bogie axle box bearing[J]. Electric Drive for Locomotives, 2018, 263(4): 6-9. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804003.htm [20] 邹纪操, 傅茂海, 李朝曦, 等. 高速变轨距动车组转向架滑动套配合量影响研究[J]. 机车电传动, 2018, 264(5): 1-4. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805001.htmZOU Ji-cao, FU Mao-hai, LI Chao-xi, et al. Research on the fit value influence of high-speed gauge-changeable EMUs bogie sleeve[J]. Electric Drive for Locomotives, 2018, 264(5): 1-4. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805001.htm [21] 孔瑞晨, 周殿买, 黄志辉, 等. 高速变轨距动车组转向架解锁-锁紧装置设计[J]. 机车电传动, 2018, 264(5): 5-8. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805002.htmKONG Rui-chen, ZHOU Dian-mai, HUANG Zhi-hui, et al. Design of unlocking-locking device for high-speed gauge-changeable EMUs' bogie[J]. Electric Drive for Locomotives, 2018, 264(5): 5-8. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201805002.htm [22] 刘晓妍, 黄运华, 张隶新, 等. 600/1 067 mm变轨距动车组转向架方案选型分析[J]. 机车电传动, 2018, 265(6): 33-37. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201806008.htmLIU Xiao-yan, HUANG Yun-hua, ZHANG Li-xin, et al. Model selection analysis of 600/1 067 mm gauge changeable bogie[J]. Electric Drive for Locomotives, 2018, 265(6): 33-37. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201806008.htm [23] CARBALLEIRA J, BAEZA L, ROVIRA A, et al. Technical characteristics and dynamic modelling of Talgo trains[J]. Vehicle System Dynamics, 2008, 46: 301-316. doi: 10.1080/00423110801939170 [24] LÓPEZ GÓMEZ J L, LACASTA AÍSA J. Talgo automatic gauge change system for freight wagons[J]. Journal of Rail and Rapid Transit, 2001, 215(1): 13-24. doi: 10.1243/0954409011530586 [25] KAISER I, VINOLAS J, GÓMEZ DELPULGAR D, et al. Contribution of variable gauge freight wheelsets to interoperability[J]. Journal of Rail and Rapid Transit, 2019, 233(5): 489-505. doi: 10.1177/0954409718804960 [26] 小田和裕, 高魁源. 可变轨距电动车的开发与试验[J]. 国外铁道车辆, 2001, 38(5): 31-35. https://www.cnki.com.cn/Article/CJFDTOTAL-GWTD200105009.htmODA K, GAO Kui-yuan. Development and test of variable gauge electric vehicle[J]. Foreign Rolling Stock, 2001, 38(5): 31-35. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-GWTD200105009.htm [27] HIDEYUKI T, TADAO O. Gauge change equipment in shin-shimonoseki depot[J]. Quarterly Reports of RTRI, 2003, 44(3): 114-116. doi: 10.2219/rtriqr.44.114 [28] KOICHI M, MINORU K, SHIGETOMO S. Development of traction motor for gauge change train[J]. IEEJ Transaction on Industry Applications, 2001, 121(5): 569-576. doi: 10.1541/ieejias.121.569 [29] TAKAO K, ISHIGE M. Structure of an independent-wheel- system bogie with a DDM and its performance at high speed[J]. Quarterly Report of RTRI, 2008, 49(4): 199-202. doi: 10.2219/rtriqr.49.199 [30] WAKIYA H. Development of gauge change train in Japan[J]. Japanese Railway Engineering, 2010, 50(2): 12-15. http://www.researchgate.net/publication/294383929_Development_of_gauge_change_train_in_Japan [31] TOKUDA N, OKAMATO I, FUJITA T, et al. Development of gauge change bogies[J]. Quarterly Report of RTRI, 2003, 44(3): 109-113. http://ci.nii.ac.jp/naid/130004457648 [32] 刘长青, 王雷. 400 km/h跨国互联互通高速动车组[J]. 机车电传动, 2020, 273(2): 1-6. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC202002001.htmLIU Chang-qing, WANG Lei. 400 km/h international interconnection high speed EMU[J]. Electric Drive for Locomotives, 2020, 273(2): 1-6. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC202002001.htm [33] 冷扬立, 李秋泽, 李庆国, 等. CRH5型动车组万向轴结构及临界转速分析[J]. 铁道车辆, 2010, 48(12): 6-11. https://www.cnki.com.cn/Article/CJFDTOTAL-TDCL201012003.htmLENG Yang-li, LI Qiu-ze, LI Qing-guo, et al. Analysis of the structure and critical rotating speed of the cardan shafts for CRH5 multiple units[J]. Rolling Stock, 2010, 48(12): 6-11. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-TDCL201012003.htm [34] 李国栋, 曾京, 李晓峰, 等. 基于变轨距高速动车组适应性的动力学性能分析[J]. 机车电传动, 2019, 270(5): 20-24. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201905005.htmLI Guo-dong, ZENG Jing, LI Xiao-feng, et al. Dynamic performance analysis of adaptability of gauge changeable high-speed EMUs[J]. Electric Drive for Locomotives, 2019, 270(5): 20-24. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201905005.htm [35] 黄志辉, 夏朝国, 胡飞飞, 等. 变轨距轮对轴套式花键的设计[J]. 机车电传动, 2018, 263(4): 1-5. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804001.htmHUANG Zhi-hui, XIA Chao-guo, HU Fei-fei, et al. Design of axle sleeve type spline of gauge-changeable wheelset[J]. Electric Drive for Locomotives, 2018, 263(4): 1-5. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC201804001.htm [36] 胡飞飞, 黄志辉, 郑志伟. 高速变轨距动车组转向架轮轴传动方案设计[J]. 机车电传动, 2020, 274(3): 30-34. https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC202003007.htmHU Fei-fei, HUANG Zhi-hui, ZHENG Zhi-wei. Design of wheel-axle transmission scheme for high-speed variable-gauge EMU bogie[J]. Electric Drive for Locomotives, 2020, 274(3): 30-34. (in Chinese) https://www.cnki.com.cn/Article/CJFDTOTAL-JCDC202003007.htm -
点击查看大图
图(10) / 表(2)
计量
- 文章访问数: 1180
- HTML全文浏览量: 510
- PDF下载量: 459
- 被引次数: 0
